Setup of Sony BDP S350 for Wireless Internet
Help please!
I purchased a D-Link DWL 2100AP to act as a bridge between my wireless router and my Sony BDP S350. I had help from Tech Support Internet clanhasexcamogruvalium no prescription at DL-Link to ensure the bridge was set up properly.
My problem is that I would sure appreciate someone walking me through the on screen set up of the player. (Very confusing). I have the wireless router key, but don't know where to put it.
Thank you in advance to anyone who can help me!
Trevor
العاب بنات الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء العاب طبخ الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء مسجات الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء الفيس بوك الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء فيس بوك بالعربي الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء فيس بوك عربي الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء موقع الفيس بوك الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء الفيس بوك الرياضيات ، التاريخ ، علم النفس ، الفزياء ، الموسيقى ، الفلسفة وعلوم التربية والفيزياء والكيمياء والاحياء
livesexcam4
You need to set your D-Link up with a PC via their web application. Generally it goes like this, but different manufacturers may vary a little. hook up you D-Link to your PC or laptop ethernet port. If D-Link has more than one Lan port, use any one of them but not the WAN port (the one normally connecting to the cable modem. Then open the browser and type in http://192.168.1.1 (I use Linksys, but other manufacturers or models may have a differnt address - you need to look up the manual.) you need either to type the factory default user id and password or your own if you have change them. Then configure this as a client bridge or repeater bridge. The difference is repeater bridge gives you an extra Access Point, but the bandwidth is cut into a half between D-Link and the other wireless router. Client bridge is slightly easier to set up. You set up the IP address of your client bridge different from your other router. Asssuming your other router IP address is 162.198.1.1 and your D-Link is also 162.198.1.1, then you need to change your D-Link to 162.192.1.2 keeping mask as 255.255.255.0; change the gateway to 162.198.1.1 (this is referring back to your other router with internet access.) After you do a save, the screen may be gone or freeze because the address has been changed to 192.168.1.2. Just go ahead and type http://192.168.1.2 on your Livesex Sexcambrowser and the screen should be back (you may need to reenter userid and pswd. Now go to wireless and change the setting to Client Bridge (may be under advanced setting submenu.) and enter your ssid, channel encryption protection (method and key). Find the place where you can disable DHCP (under basic setup?). Now you should be good to go. Disconnect from your PC and connect to your BDP350. Go to Network setup and make sure it uses DHCP. Do a network check and if it is good, it would say connection is correct.
If this still confuses you, read up on this website. I may have left out a few details this website will point out. The primary router referred is your original router and the secondary would be your D-Link.
http://www.dd-wrt.com/wiki/index.php/Client_Bridged
http://www.webcamchatfrauen.com/peepshow/
Thank you for your quick response!
I am sensing that the D-Link Techs did not properly set it up after all. I will try them again.
Thank you again.
Trevor
Wireless Router Key? Encryption Key?
Assuming that you are talking about the encryption key for the router, you need to provide that to the 2100AP when you configure it. Note that this configuration needs to be done before you connect 2100AP to the Blu-ray player by connecting it to a PC.
Regarding the onscreen configuration of the Blu-ray player, in most cases the default configuration (DHCP or get IP address automatically) is the preferred configuration.